SPECTRAL IMAGING/MICROSCOPY/ENDOSCOPY: Fast and efficient, image mapping spectrometry advances bioimaging

By Tomasz Tkaczyk

A light-efficient, non-scanning hyperspectral technique, image mapping spectrometry offers several advantages for biological and medical imaging, including high SNR, reduced photobleaching, and discernment of multiple, densely packed spectral signatures. The approach is promising for rapid imaging and processing, among other applications.

Partly because of recent advances in camera development (for example, large-format, high-speed and spectral-range arrays), and partly because of its ability to reveal the chemical composition of objects, spectral imaging is increasingly regarded as an important tool in biological and medical imaging.

The technique can image biological samples at multiple wavelengths simultaneously (see Fig. 1). High imaging speed allows imaging fast processes for example calcium oscillations, while high spectral sampling enables imaging of similar signatures—for example, fluorescent proteins (GFP, YFP, CFP and others) separated by only few nanometers. It also allows processing of an increased number of separate spectral signatures, and therefore improved imaging throughput.

FIGURE 1. Bovine pulmonary artery endothelial (BPAE) cells, stained with MitoTracker Red CMXRos, Alexa Fluor 488 phalloidin, and DAPI, were imaged using an image mapping spectrometry (IMS) prototype instrument. The dozen 350 × 350 spectral images represent a total of 48 acquired simultaneously; they show ~0.5 µm resolution and spectral sampling over a 200 nm range with all image detail preserved. Filter sets by Chroma (61001 DAPI/FITC/Propidium Iodide) were used to select the excitation wavelength and separate the fluorescent signal from the excitation light. (Images courtesy Rebellion Photonics Inc.)

Depending on the application, spectral sampling spans from a few bands in clinical applications like monitoring of blood oxygenation to tens of bands in cell signaling1—and different applications target different spectral ranges, such as the visible range for cell signaling (fluorescence microscopy) and infrared (mid- and long-wave, or MWIR and LWIR) for gas and chemical detection in general.

Approaches and instruments

The available hyper- and multispectral instrumentation provides a variety of technological solutions to address different application requirements. The broadest categories of hyper- and multispectral imaging modalities are scanning and snapshot techniques. Scanning methods can be further split into spatial scanning (point, line, and disc scanning) and filter-based spectral scanning, with liquid crystal tunable filters (LCTFs) and acousto-optic tunable filters (AOTFs).2-4 Snapshot approaches are more diverse and include, for example, aperture splitting, aperture coding, computed tomography and image slicing.5-8

The selection of approach is critical, as it defines the acquisition speed—and thus the light budget and signal-to-noise ratio (SNR), as well as the extent of data reconstruction and processing. Scanning methods, for example, impose a tradeoff between the dwell time and spectral cube dimension (x, y, λ)—in other words, among image size, overall imaging speed, and SNR. The data in these scanning modalities is usually obtained directly and requires only modest post-processing. Similar in that regard is the non-scanning, aperture-splitting approach, which suffers significant light loss proportional to the number of applied filters. Snapshot techniques such as aperture coding and computed tomography imaging spectrometry are computationally intensive, while the majority of image-slicing methods require an extensive infrastructure for numerous spectrometers.

Scanning techniques are quite successful for applications requiring high spatial or spectral resolution while at the same time allowing a compromise in speed or signal level. In addition, in many bioimaging applications the short dwell and integration time can be at least partially compensated by increasing the power of the light source.

Most snapshot techniques, on the other hand, are still in development, awaiting a broad application opportunity. One of the most promising of these is image mapping spectrometry (IMS), which has great potential for wide implementation.9-11 To the best of my knowledge, no other snapshot technique currently available is capable of similar high light throughput (~85%) and data cube dimensions (350 × 350 × 48 x, y, λ) for real-time acquisition, analysis and display.

Image mapping spectrometry

IMS works by spatially redirecting image zones to obtain space between image segments/pixels by means of a redirecting mapping mirror also called the “image mapper.” Next, by using a dispersive element, IMS obtains wavelength spread on the large format CCD or CMOS camera. Segment/pixels are grouped and imaged through the dedicated optics of a re-imaging lens array. This makes the entire system more compact and effectively applies 90–95% of a CCD/CMOS image sensor. Because IMS maps each voxel (x, y, λ) to a unique pixel of the 2-D image sensor, the entire spatial-spectral information can be acquired with no scanning in a single integration event.

No significant computation or processing is required to create the full 3-D (x, y, λ) data cube, as the data is acquired directly. Simple image re-mapping is sufficient to reconstruct the object. This way, the IMS system offers fundamental advantages in imaging speed and signal collection efficiency over current methods for spectral imaging. For example due to parallel acquisition it has a longer dwelling time comparing to scanning techniques, thus can collect more photons while still retaining a high frame rate. Direct data acquisition also allows real-time display and data analysis, avoids reconstruction artifacts, and can provide diffraction-limited performance.

FIGURE 2. Critical components in an IMS system are a three-segment mapping mirror, an array of dispersers and reimaging lenses, and a large-format 16 Mpix CCD image sensor.

IMS was initially developed for microscopy applications and the technology is currently being transitioned to the medical field—for microscopy and endoscopic cancer detection—in addition to remote sensing. Critical system components in this IMS layout are a three-segment mapping mirror, an array of dispersers and reimaging lenses, and a large-format, 16 megapixel (Mpix) CCD (Imperx; see Fig. 2).

An important advantage of the IMS system is versatility: It can be built as a stand-alone system or combined with other imaging modalities. Specifically, it can replace the detector of any given imaging system to add real-time spectral resolving capability in both microscopy and endoscopy applications, for example (see Fig. 3). Note that the use of IMS in intact tissues can be easily enhanced by incorporation of an optical sectioning capability—through structured illumination, Nipkow disk confocal, or 3-D spatial deconvolution systems, for instance.

FIGURE 3. IMS results (above) and implementations (below) obtained in two biomedical applications. Unmixed pseudo-color fluorescent protein components and merged microscopy images (a) of triple-labeled Hela cells (expressing ECFP in the mitochondria, EGFP on the on the plasma membrane, and SYFP in the nucleus) were obtained over a 500 ms integration time using a Zeiss Axiovert microscope with 40x, 0.75 NA objective. Wide-field reflectance mode microscopy images, showing in-vivo oral tissue (b) in eight selected channels and RGB composite, highlight vasculature in approximately 5 mm diameter field of view. The use of IMS in intact tissues can be easily enhanced by incorporation of an optical sectioning capability by easy combining IMS with structured illumination, Nipkow disk confocal, or 3-D spatial deconvolution systems. (Samples courtesy of Prof. D. Piston’s lab at Vanderbilt University)

Overcoming disadvantages

A limitation of current spectral imaging is the lack of reliable real-time feedback to the user. For example, during imaging experiments involving calcium (Ca2+), one generally plots the Ca2+ indicator dye intensity trace continuously to check for normal behavior before adding experimental perturbation. If the Ca2+ indicator dye signal is buried among other similar spectral signals, however, such monitoring becomes very difficult. Spectral unmixing allows one to separate spectrally similar dyes—though it needs to be combined with real-time data-cube measurements. IMS provides this capability; Figure 4 shows an example of unmixing done in real time. While IMS has numerous advantages, its primary constraint is that the dimension of the data cube depends on the size of the image sensor. This means that the total number of voxels cannot exceed the total number of pixels on the camera, although it is possible to increase the spatial sampling at the expense of spectral sampling, and vice-versa. So for example, a 1024×1024 pixel camera can build a data cube (x, y, λ) either in the 256 × 256 × 16 or 512 × 512 × 4 formats (the first two numbers describe spatial sampling, and the third one indicates spectral sampling). Realizing higher spatial and spectral sampling simultaneously requires a larger format camera. Large-format CCD cameras available currently have 16+ Mpix, allowing the IMS to acquire data cubes up to 500 × 500 × 64. Note, however, that currently available CCDs used in aerial photography allow acquisition of images using 60 to 250 Mpix formats, while infrared cameras allow 1 Mpix format (in both MWIR and LWIR). On the other hand, consumer-grade cameras have recently reached 85 Mpix resolutions. So it seems clear that further extension of IMS data cube dimensions will be easily implementable in the near future.

FIGURE 4. BPAE cells stained with MitoTracker Red CMXRos, Alexa Fluor 488 phalloidin and DAPI were unmixed and pseudo-colored for demonstration of unmixing capabilities (a). Imaging and unmixing was performed at 7.2 fps. To produce a panchromatic image of the same sample location (b), 48 spectral channels were obtained simultaneously and used for processing. (Images courtesy of Rebellion Photonics Inc.)

The IMS technique has a great potential for biological and medical imaging. The snapshot mode and high light collection efficiency allow high SNR while reducing photobleaching effects, and is also advantageous in applications where light source compensation is impossible. Spectral range and resolution enable IMS to distinguish among multiple spectral signatures, even those that are densely packed. So, IMS presents as a powerful new modality for hyper- and multispectral applications, and as time goes on, it is likely to fill the imaging space for low signal applications, rapid imaging and processing for biological imaging, medical imaging and numerous other applications.

REFERENCES
1. M.A. Rizzo and D.W. Piston, Biophys. J. 88, L14–16 (2005).
2. Carl Zeiss MicroImaging GmbH, Jena, Germany, LSM 710 product brochure, www.zeiss.com.
3. ChromoDynamics, Inc., Orlando, FL, HSi-300 hyperspectral imaging system data sheet, www.chromodynamics.net.
4. Cambridge Research and Instrumentation, Inc., Cambridge, MA, VARISPEC liquid crystal tunable filters brochure, www.cri-inc.com.
5. D.B. Duncan and G. Leeson, Proc. SPIE 3649, 100 (1999).
6. C. F. Cull et al., Appl. Opt. 49 (10), B59–B70 (2010).
7. B. Ford et al., Opt. Exp. 9 (9), 444–453 (2001).
8. F. Hénault et al., Proc. SPIE 5249, 134–145 (2004).
9. L. Gao et al., Opt. Exp. 17 (15), 12293–12308 (2009).
10. L. Gao et al., Opt. Exp. 18 (14), 14330–14344 (2010).
11. R.T. Kester et al., J. Biomed. Opt. 16 (5), 056005 (2011).

More BioOptics World Current Issue Articles
More BioOptics World Archives Issue Articles

Get All the BioOptics World News Delivered to Your Inbox

Subscribe to BioOptics World Magazine or email newsletter today at no cost and receive the latest news and information.

 Subscribe Now
Related Articles

Merz acquires laser tattoo removal device maker ON Light Sciences

Merz North America has acquired ON Light Sciences, which develops technologies to enhance laser-based dermatology procedures.

Shortwave-infrared device could improve ear infection diagnosis

An otoscope-like device that could improve ear infection diagnosis uses shortwave-infrared light instead of visible light.

Laser therapy extracts rare tumor that grew human hair, skin in boy's skull

About four years ago, a tumor comprised of human skin, hair, bone and cartilage was fast-growing inside a Ramsey, MN, 10-year-old youth's brain.

Low-level laser therapy could speed muscle recovery at Rio 2016 Olympics

The gold medal-winning women’s U.S. Gymnastics team is reportedly experimenting with infrared light therapy to alleviate pain and reduce swelling in its athletes. (Update: A spokesperson for ...
BLOGS

Neuro15 exhibitors meet exacting demands: Part 2

Increasingly, neuroscientists are working with researchers in disciplines such as chemistry and p...

Why be free?

A successful career contributed to keeping OpticalRayTracer—an optical design software program—fr...

LASER Munich 2015 is bio-bent

LASER World of Photonics 2015 included the European Conferences on Biomedical Optics among its si...

White Papers

Understanding Optical Filters

Optical filters can be used to attenuate or enhance an image, transmit or reflect specific wavele...

How can I find the right digital camera for my microscopy application?

Nowadays, image processing is found in a wide range of optical microscopy applications. Examples ...

CONNECT WITH US

            

Twitter- BioOptics World